The job of a lift cable
On a typical residential garage door with torsion springs, there are two lift cables, one on each side of the door. Each cable is attached to a bracket at the bottom corner of the door, runs up along the side of the door and winds onto a drum at the end of the torsion shaft. When the shaft turns, the drums turn with it and pull the cables up, lifting the door. When the door goes down, the cables unwind from the drums.
This means the cables carry the weight of the door. The spring supplies the lifting force, but the cable is the link that transmits it. If a cable fails, the spring can no longer lift that side of the door, and the door can become crooked, jam in the track or drop.
Because the cables are under load whenever the door is closed or moving, they are built from strands of steel wire twisted together. This makes them strong and flexible, but each strand can wear. A cable is not a permanent part. It is a wear item that needs to be checked, and replaced when it shows its age.
How cables are routed and seated
The path of a cable matters. At the bottom, it connects to the bottom bracket, which is bolted to the door near the corner. From there it runs straight up in the small gap between the door and the vertical track, without touching the track or the roller. At the top, it reaches the drum, which has spiral grooves cut into it. The cable sits in those grooves as it winds on, and the grooves keep each turn neatly in place.
When the door is fully closed, the cable is wound onto the drum with a few turns, and it is tight. When the door opens, more cable winds on, and the drum draws it in. If the cable is not seated properly in the groove, or if it has slipped off the drum, it can bunch up, wind unevenly and fray quickly.
Our page on cable drum problems goes deeper into drums and what happens when they wear. For now, the key point is that routing and seating must be right for the door to lift level.
Signs of cable wear
Lift cables rarely fail without any sign. Fraying is the most common, and it often begins near the bottom bracket or at the drum, where the cable bends or rubs. You may see small wires sticking out, a section that looks furry or a spot where strands have broken. Rust is another sign, especially in humid garages where the cable has been damp for long periods.
Other signs include a cable that looks uneven in length from side to side, one that hangs loose when the door is closed, or one that has jumped off the drum. A door that tilts as it rises, with one side higher than the other, may be telling you that a cable is slack or one side is worn.
Sometimes you notice a change in sound, such as a scraping or rubbing noise as the door travels. That may be a cable rubbing against the track or the roller. Take these changes seriously, because a cable that is worn is close to failure, and a failed cable can drop the door.
Look from a safe distance only. Do not touch the cables while the door is moving or under tension, and do not pull on a loose cable.
- Strands sticking out, fuzzy sections or visible broken wires.
- Rust or heavy dark staining along the cable.
- A cable that hangs loose or is off the drum.
- A door that rises or closes crooked.
- A scraping noise as the door moves.
- A cable that looks different in length from the one on the other side.
Why a snapped or loose cable is a serious problem
If a cable snaps, the spring stored energy can no longer be used to hold that side of the door. The door may fall on one side, twist in the track and jam. If the door was open at the time, it may drop suddenly. This is a real risk for anyone standing underneath or for a vehicle parked near the door.
A cable that comes loose from the drum is nearly as bad. The cable may wrap around the shaft or get caught in other hardware. The door can be left hanging crooked, with one corner lower than the other. Attempting to run the door with the opener in that state can bend the track, warp the panels and strain the opener.
If you see a snapped or loose cable, stop using the door. Do not try to raise or lower it. Keep people and pets away from the door and call. Our page on a snapped garage door cable describes what owners notice when this happens and what to do.
What causes cables to fail
Cables wear for a few reasons. Age and cycles are the main ones, because each trip bends the cable around the drum and puts tension through it. Rust speeds this up by weakening the steel, and South Florida humidity and salt air make rust a common issue. Cables that are never inspected can quietly reach the end of their life.
Mechanical problems also cause wear. A door that is out of balance, a drum that is worn, or a bracket that is bent can all make the cable rub or kink. A track that is out of alignment can cause the cable to scrape. Rollers that are stuck can cause the door to hang, which puts uneven load on a cable.
A cable can also be damaged by impact. If a vehicle has bumped the door, or if the door has been struck by something, the bottom bracket and cable may be bent or stressed. Even if the door seems to work afterward, a damaged cable may fail later.
Why cable work should be left to a technician
Cables are connected to springs that hold a lot of tension. Even a cable that looks simple to remove is attached to a system under load, and releasing it in the wrong way can cause the drum to spin, the shaft to turn or the door to drop. The bottom bracket is also under spring tension, and it can fly off if loosened without care.
For this reason we do not recommend owners attempt cable replacement. The risk of injury is real, and the work involves handling the torsion springs. Even removing a cable from a drum requires the system to be secured and the tension to be controlled.
What you can do is observe and report. Take note of where the cable is frayed or off, what the door does, and any sounds. Call and describe it. A technician can inspect and, if needed, replace the cable, and also check the drum, bracket and spring.
What a technician does when replacing cables
The technician begins by securing the door and relieving tension in a controlled way. They remove the old cable from the drum and the bottom bracket, and inspect both for wear. A worn drum or bent bracket is replaced at the same time, because a new cable on a damaged part will wear out quickly.
The new cable is cut to the right length and attached to the bottom bracket. It is seated in the drum groove and routed along the track without touching it. The spring is then wound to the proper tension, and the technician checks that both sides are even. They test the door by hand and with the opener to confirm that it rises level and stays balanced.
In most cases, both cables are replaced together. The two cables share the work and wear at similar rates, so if one has frayed, the other is often not far behind. Ask the technician to show you the cable they removed and explain what they saw. Our page on how spring replacement works describes the broader process.
Looking after cables and when to call
You can help your cables last by watching them. Whenever you are in the garage, glance at the cables from a safe distance. Look for fraying, rust and loose ends. Listen for scraping. If the door starts to rise crooked, stop using it. Keep the bottom of the door and the track area clear of clutter and moisture, and keep vehicles from bumping the door.
Professional inspections are the best way to catch wear early. A technician can examine the cable at the drum and bracket, where fraying usually starts, and check that everything is seated properly. See our annual inspection guide for what to expect.
If you see a damaged cable, call. Describe what you see and what the door is doing. Quotes are given by phone for simple work, and the service call charge is explained before anyone is sent. If the cable has snapped or the door is stuck, we will tell you what to do until a technician can look at it.
Cables on extension spring doors
Doors with side mounted extension springs use cables differently. Instead of winding onto a drum, the cable runs from the bottom bracket up past the roller, over a pulley at the front of the spring and back along the track to an anchor point. The cable is part of the pulley system that lets a short spring lift a heavy door. The same signs of wear apply, but the places where fraying occurs are different, such as at the pulley and the anchor.
Pulleys can seize or wear, and a cable that passes over a dry pulley wears quickly. An anchor that rusts can loosen. And because extension spring systems are often older, the cables have usually been through many cycles.
When an extension spring door is serviced, the technician inspects the cables along with the pulleys, springs and safety cables. See our page on extension springs to understand how the system fits together.
Humid climate and cable life
Steel cable is built from many strands of wire, and moisture can get between the strands. In a humid climate, a cable that is never dry can rust from the inside out. The outside may look acceptable while the inside is weakened. This is one reason cables on South Florida doors can reach the end of their life earlier than owners expect.
Cables near the bottom of the door are also exposed to splashes and standing water. During the rainy season, water running under the door or pooling at the threshold can wet the lower bracket and cable. After a flood, the lower hardware may have been submerged. If your garage has had water in it, have the cables and brackets checked even if the door still works.
Our guides on rainy season care and flood water damage describe what to look for. A short inspection can find early rust or fraying and let a cable be replaced before it fails.
Preparing for a cable repair visit
Before the technician arrives, clear the area in front of and around the door. If a vehicle is inside, leave it where it is unless you can move it without raising the door. Keep everyone, including pets, away from the door and the track. Do not try to untangle a loose cable or pull it back onto the drum.
Make a few notes for the call. Which side is affected? Did you hear a snap or a bang? Is the door stuck open, closed or partway? Was there any recent impact or water in the garage? If you can take a photo from a safe distance of the bottom corners of the door, it can help the technician bring the right parts.
Tell us if the garage is part of a managed property, since access may need to be arranged. Then call, describe what you see and ask about the service call charge, which is explained before anyone is sent.
Questions people ask
How many cables does a garage door have?
Most residential doors with torsion springs have two lift cables, one on each side. Extension spring doors also use cables with pulleys on each side. Both sides share the load and should be in similar condition. If one is worn, a technician often recommends replacing both.
What should I do if a cable has come off the drum?
Stop using the door. Do not run the opener or try to lift the door by hand, because it may be crooked or unstable. Keep people and pets away from it and call. The technician will secure the door, reseat or replace the cable and check the drum.
Can I just replace one cable?
It is possible, but both cables have done the same work and wear at similar rates. Replacing both keeps the door lifting level and avoids another visit soon. A technician can look at the second cable and explain whether it is worth keeping.
Why is my cable fraying near the bottom?
Fraying often starts where the cable bends or rubs, such as near the bottom bracket or at the drum. Rust, age and balance problems all contribute. Fraying is a sign the cable is near the end of its life, so have it checked before it breaks.
Is a loose cable dangerous?
Yes. A loose or off-drum cable can leave the door crooked, jammed or unable to hold weight, and it can drop. Do not use the door and keep people clear. Call and describe what you see so a technician can make the door safe.
How do I get a cable replacement quoted?
Call and describe the cable, the door and what it does. We explain the service call charge and give a quote by phone for straightforward work. If other parts are damaged, the technician explains that on site before any added work. Call whenever you are ready.
For "Lift Cables Explained", a phone call comes first. Describe the springs, the opener or the panels, and we will explain how the work is done and what the visit charge covers.
Related pages
Choosing the right cable length and construction
A lift cable is not a one size part. Its length depends on the height of the door and the way it is wound, and its diameter and strand construction depend on the weight it must carry. A technician measures the existing cable if it is intact, and also checks the drum type, the door height and the spring configuration to confirm that what was installed originally is correct. Installing a cable that is a little too short or too long will leave the door hanging unevenly or cause the cable to slacken at the top of its travel.
Construction matters as well. Cables are made of many fine strands twisted together, and the number of strands and the way they are wound affect flexibility and fatigue life. A cable that is too stiff for the drum diameter may bend sharply and wear sooner. A cable that is rated for less weight than the door needs may stretch or fail under load. These details are why parts are matched to the door, not bought by looks, and why a guess based on a single photograph is rarely enough.
When you call, helpful information includes the width and height of the door, whether it has one spring or two, whether the springs run along a shaft above the door or sit beside the tracks, and the approximate age of the door. Do not remove or loosen a cable yourself, since it is connected to a system under heavy tension. We will explain the scope of the work and the quote before any work begins, and nothing is added without your agreement. Photos of the door and any labels, taken from a safe distance, are also welcome and can shorten the conversation.
