What dragging on one side looks like
A healthy door travels level. Both lower corners rise together, the panels stay parallel to the floor and the door settles evenly when closed. When one side drags, you will notice the door tilting as it moves. One bottom corner may rise sooner than the other, or one side may lag behind and then catch up with a jolt. When the door is closed, a gap may show along one end of the bottom edge, or one side may rest harder against the floor than the other.
You may also hear it. A dragging door often scrapes, squeals or groans on one side, and the opener may sound strained because it is pulling a load that is not balanced. Sometimes the door stops partway because the opener senses extra resistance and shuts off for safety. In other cases the door travels the whole way but wears one track, one set of rollers and one cable much faster than the other side.
It helps to describe the pattern precisely. Which side is lower? Does it happen going up, going down or both? Did it start suddenly or build up over weeks? Is there a visible gap or a rubbing mark? Those details point toward the cause. Taking a short video with your phone from inside the garage, standing well clear of the door, is one of the most useful things you can give a technician.
- Note which side is lower and whether the tilt shows going up, going down or both.
- Record a short video from a safe distance while the door moves.
- Look for fresh scrape marks on the track, the jamb or the floor.
Why the two sides stop sharing the load
A sectional garage door is lifted by two cables, one on each side, wound around drums on a shaft above the door. The springs supply the lifting force, and the cables transfer it to the bottom corners. The rollers on each side follow the tracks. When everything is matched, both sides lift equally. When any piece on one side changes, the door begins to twist as it moves.
The most common cause is a cable that has slipped, stretched, frayed or come off its drum. If one cable is looser than the other, that side of the door is held up less firmly and drops lower. A second cause is a roller that has jammed, cracked or jumped out of the track on one side. A third cause is a bent or misaligned track that makes the rollers bind. A fourth is a spring that has lost strength or has broken, particularly in a two-spring system where one spring is weaker than the other.
Less often, the cause is structural: a door section that has cracked, a hinge that has pulled loose from a panel, or a header and jamb that have shifted. Each of these changes the geometry of the door and the way the load moves through it. See our page on a crooked or uneven garage door for related patterns.
Uneven cable tension
Cable tension is the first thing a technician checks. The two cables should be equal in length and tension when the door is closed and again when it is open. If one is slack, that side is not carrying its share. Cables loosen when a cable slips on its drum, when a set screw works loose, when the cable frays or snaps, or when a roller pops out and lets the bottom bracket drop.
A frayed cable shows broken strands that look like fine wire hairs, usually near the drum or the bottom bracket. A cable that has come off its drum may hang loosely or tangle. A snapped cable leaves one corner of the door unsupported, and the door may hang crooked or fall to one side. Do not touch the cables. They are under high tension, and a sudden release can injure.
If you see slack, fraying or a cable out of its groove, stop using the door and call for service. Running the opener on an unbalanced door risks further damage to the cable, the drum, the track and the opener itself. Read the garage door cables guide and cable drum problems for more on how cables fail.
- A slack cable on one side is a stop-and-call sign.
- Fraying near the drum or bracket means the cable is nearing failure.
- Never touch, loosen or adjust cables or drum set screws yourself.
Worn, cracked or stuck rollers
Rollers are small wheels that ride in the tracks and carry the door as it moves. Most doors have a roller on each side of every section. Over time they wear, flatten, crack or seize. A roller that no longer turns drags along the track instead of rolling, and it adds friction on that side.
You can sometimes see a seized roller from the floor. The wheel may not rotate when the door moves, or it may wobble on its stem. Metal rollers without bearings, common on older doors, wear quickly and make a grinding noise. Nylon rollers with bearings last longer and run quieter but still wear. A roller that has popped out of the track leaves the door hanging on one side.
Do not try to push a roller back into the track while the door is unsupported. The door may shift or fall. Roller replacement is a job for a technician, who can support the door safely. For more on how rollers work and when they should be replaced, see the garage door rollers guide and a roller popped out of the track.
Tracks that are bent, loose or out of line
The tracks hold the door's path. A track that has been bumped by a vehicle, bent by wind or loosened by vibration no longer guides the rollers properly. On one side, the track may be closer to the wall or farther from it than on the other, or it may slope. That makes the door ride higher or lower on that side and can pinch the rollers.
Look at the tracks from inside the garage. The vertical sections should be straight and parallel, and the distance between each track and the door should be consistent. A dent or a kink in the metal, a loose bolt on a bracket or a gap between a bracket and the wall are warning signs. Rust and debris at the bottom of the track can also create friction.
Tightening a few visible track bolts may be safe for a careful homeowner when the door is closed and the opener disconnected, but track adjustment is a precise job. A track bent out of line needs to be straightened or replaced. Never hammer a bent track while the door is hanging on it. See the tracks guide and bent track for details.
Springs that are unequal or failing
The spring system counts on balanced forces. Many doors use two torsion springs on a shaft, and some use one. Extension springs, found on older doors, come in pairs along the tracks. If one of a pair breaks or weakens, the door loses lifting force on that side, or the shaft transmits uneven torque.
A broken torsion spring often leaves a visible gap in the coil. The door may feel very heavy and the opener may strain. A weak spring may show no gap but allow the door to sag. Mismatched springs, installed at different times and with different wear, can also cause uneven behavior.
Springs hold a lot of stored energy and should never be adjusted by a homeowner. If you suspect a spring problem, keep the door closed if you can, disconnect the opener from power and call for service. Read the torsion spring guide and the extension spring guide to see how the systems work.
- A visible gap in a torsion spring coil means it has broken.
- A door that feels very heavy points to lost spring force.
- Replace springs as a matched set when advised, so that wear stays even.
Safe checks you can do yourself
There are a few safe observations a homeowner can make. With the door closed and the opener left alone, stand inside the garage and look at the bottom corners. Is one higher or lower than the other? Is there a gap under one end? Look at the cables from a distance and see whether they appear equally tight. Look at the tracks and the rollers for visible damage or debris.
Check the wall-mounted opener's light and listen to its sound. If it hums but does not lift, the cause is likely a spring or a cable. If it lifts but the door tilts, the cause is likely a cable, a roller or a track. Do not run the door repeatedly to test. Each attempt can worsen the damage.
Wipe debris from the lower tracks with a dry cloth. Do not use lubricant on the inside of the tracks. Do not tighten or loosen any part of the spring or cable hardware. If you see a roller out of the track, a slack cable or a gap in a spring, stop. Our safety checklist and warning signs guide list what is safe to do and what is not.
- Disconnect the opener from power if the door is behaving oddly.
- Look from a safe position at both bottom corners, cables and tracks.
- Clear visible debris from the lower track with a dry cloth.
- Do not touch springs, cables, drums or end brackets.
- Call for service if anything looks slack, bent, frayed or out of place.
What a technician will check
A technician begins with safety and a visual survey. They will look at both sides of the door at the same time, compare cable tension and drum position, check each roller and hinge, inspect the tracks for alignment and look at the springs and shaft. They will disconnect the opener and test the balance by lifting the door by hand, which shows how well the springs carry the weight.
They will then decide what to correct. It may be as simple as resetting a cable on its drum and tightening a set screw, or as involved as replacing a cable, a drum, several rollers and a section of track. If a spring is weak or broken, they will explain what size is needed for your door. If a panel or hinge has cracked, they may recommend replacing the section.
Ask what caused the problem. If a vehicle bumped the track, or a roller seized because of a lack of lubrication, you will want to know so that it does not happen again. Ask the technician to explain what else is worn, so that you can plan for future repairs. See cable and roller repair for what the work includes.
Why you should not keep running it
It is tempting to keep using a door that still moves. The trouble is that a door dragging on one side is destructive. The friction wears the track and rollers, the cable on the loaded side stretches, the drum may deform and the opener's gears take shock loads. A problem that began with one worn roller can turn into a bent track, a snapped cable and a damaged opener.
There is a safety issue too. A door that tilts can come off its track and fall. A door that hangs lower on one side may jam when it meets an obstruction, and the auto-reverse may not work as designed. Children, pets and vehicles near the door are at risk.
If the door is still working and you cannot get service right away, use it as little as possible, and use it only with nobody near it. If the door stops, do not push it. If it is open and unstable, keep clear and call. Our page on emergency garage door closure explains how to secure an opening safely.
South Florida factors that make it worse
Heat, humidity and salt accelerate wear. Cables and brackets rust, rollers lose lubrication, and tracks collect leaves, grit and moisture. Afternoon storms push water and debris into the lower track. A door that sat unused for a few weeks while you were away may seize on one side from corrosion.
Strong wind can also bend a track or push a door out of line. After a storm, check the door for unevenness before using it. If the door was hit by debris or a vehicle, assume something is out of alignment. Read the garage door after a hurricane for what to look for.
Regular care helps. Wipe the hardware, lubricate hinges and roller stems as advised, check the tracks and test the balance. When you notice one side lagging, act early, because the repair is smaller and the door is safer. When you are ready, call, describe the problem and a person will talk through the next step.
Questions people ask
Why does one side of my garage door hang lower than the other?
The two sides are no longer sharing the load. The most common causes are a slack or frayed cable, a roller that has seized or popped out, a bent track or an uneven spring. The door may tilt going up, going down or both. Stop using it and have it checked rather than running it repeatedly.
Can I fix an uneven garage door myself?
The parts that cause this problem, cables, springs, drums and brackets, are under high tension and are not safe for homeowners to adjust. You can safely observe, take photos and clear debris from the lower track. Leave adjustments and replacements to a trained technician.
Is it safe to keep using the opener if the door is lopsided?
It is not recommended. The door may come off its track, the cable may snap and the opener may be damaged. If you must use it, do so only when nobody is near and use it as little as possible. Call for service soon, since the repair is usually smaller the earlier it is caught.
Could a bad opener cause one side to drag?
Rarely. An opener pulls from the center, so uneven travel usually comes from the door's own parts: cables, rollers, tracks or springs. The opener may show strain as a result. A technician will check the door's balance with the opener disconnected to find the true cause.
How do I know if a cable has come off its drum?
You may see a loose or hanging cable at one side, a cable that no longer sits in the drum groove or a door that hangs crooked. Do not touch it. The cable is under tension and the door may be unsupported. Stop using the door, keep people clear and call for service.
How are repairs quoted?
Quotes are given only by phone. Call, describe the symptoms and the dispatcher explains the service call charge before dispatch. Simple repairs can often be quoted over the phone, while a complicated job, such as a damaged track or sections, may need an on-site visit before a firm quote.
If "Garage Door Drags on One Side" is the problem at your house, call and describe what the door is doing. We explain what a repair visit would cover, and the service call charge is stated on the phone before anyone is dispatched.
