What an inspection is, and what it is not
An inspection is a professional examination of the door, the opener and the safety devices to find wear, damage and adjustment problems before they cause a failure. It is not a repair, although a technician may fix small things on the spot. It is not a sales visit either. A good inspection ends with a clear explanation of what the technician found: what is in good order, what is wearing, what needs attention soon and what needs attention now.
The word annual is a convenient label, not a rule. A door that is used many times a day, sits near salt water or is already old may justify a visit more often than once a year. A lightly used door in a sheltered garage may need it less often. What matters is that the door is looked at by someone trained to see what an owner cannot, with enough regularity that wear is caught while it is still simple to put right. We never quote over the web, so any cost question is answered on the phone.
Owners can and should do their own checks in between, as described in our home safety checklist. But there is a set of tasks that only a trained technician should carry out: measuring spring condition, testing balance safely, inspecting cables and drums under load, checking bottom brackets and adjusting opener limits and force. The inspection exists for those.
Where the technician starts: the first look and the questions
A technician usually begins by looking at the door in its normal state and asking about its history. How long has it been in place? Has it been repaired or modified? Are there noises, slow movement, a door that reverses, a remote that is flaky or a sensor that misbehaves? Your answers help direct the inspection, so tell them everything, even things that seem minor.
They will look at the door from inside and outside before touching anything. They check that it sits level and square in the opening, that panels are straight and that nothing is visibly damaged. They look at the tracks, the springs, the cables and the opener from a safe distance, spotting obvious problems such as a gap in a spring, a frayed cable, a bent track or a loose bracket. If anything looks hazardous, they secure the door first.
Then they run the door on the opener through a full cycle, watching and listening. They note the speed, the smoothness, the sounds and how the door stops at the top and bottom. This gives a baseline before any hands-on checks. It is also where an experienced technician often hears the early sign of a worn roller, a dry hinge or an opener gear starting to go.
Springs, cables and drums
The springs are the heart of the door. On a torsion system, the technician looks at the spring or springs above the door, checking for gaps in the coils, signs of stretching, rust, cracks and the condition of the winding cones and set screws. On an extension system, they check the springs along the tracks, the pulleys and the safety cables that contain a broken spring. They estimate how close the springs are to the end of their cycle life based on size, wire gauge and use.
Cables run from the bottom brackets up to the drums or pulleys. The technician checks for fraying, broken strands, kinks, rust and signs that a cable has slipped or is worn at the ends. Rust at the lower end of a cable, where it meets the bottom bracket, is common in coastal areas and is an important sign. They check the drums for wear and for how well the cable sits in the grooves.
These are the highest-risk parts of the door, and the technician will take care to follow safe procedures, using proper tools and securing the door as needed. If anything is worn, they will explain why it matters. A cable or spring that is near the end of its life is a good candidate for planned replacement, rather than waiting for it to fail. Our guide on spring cycle life explains why springs wear out in a predictable way.
Balance, tracks, rollers and hinges
Next comes the balance test, with the opener disconnected and the door secured. The technician lifts the door by hand and sees whether it stays in place, drops or rises. A balanced door shows the springs are doing their job. An unbalanced door points to worn springs, a cable issue or a binding track. They will interpret the result alongside what they have seen. Our page on the balance test explains its value and limits.
They inspect the tracks along their length for dents, bends, gaps at joints and loose mounting bolts. They check that the tracks are parallel and properly aligned with the door. Rollers are examined for flat spots, cracked wheels, worn bearings and play in the stems. Hinges are checked for cracks, bent leaves, loose pins and wear at the pivot. These small parts determine how quietly and smoothly the door moves.
They also look at the panels themselves, checking for cracks, dents, delamination and signs that the sections are separating. On wood doors they check for moisture damage and rot. On aluminum and glass doors they look at the seals and the glazing. In South Florida they pay attention to corrosion at hardware and the bottom edge, since the combination of moisture and salt air is hard on steel.
- Torsion or extension springs, winding cones, set screws, safety cables.
- Lift cables, drums, pulleys and bottom brackets.
- Balance with the opener disconnected.
- Tracks, track brackets, rollers and hinges.
- Panels, struts, seals and weather stripping.
- Fasteners and mounting to the building.
The opener, limits, force and safety devices
The technician then turns to the opener. They check the mounting, the rail, the chain, belt or screw, the trolley or carriage and the connection to the door. They listen for gear noise and look for wear, slack and damage. They check the travel limits, which tell the opener where the door should stop at the top and bottom, and the force settings, which determine how hard the opener will push before it senses a problem.
The safety devices get close attention. The technician tests the photo-eye sensors for alignment and function, usually by blocking the beam with a test object and watching the door reverse. They test the contact reversal by placing a solid object in the path of the closing door. If either test fails, they investigate the cause, which may be dirt, misalignment, wiring, a worn sensor or an incorrect setting. They will not leave a door in service with failed safety devices.
Remote controls, keypads and the wall control are checked too. The technician tests each device, looks at batteries and may suggest reprogramming if a device is lost or an old tenant has had access. They also check the opener's light, the manual release and any battery backup. For more on openers, see opener types explained and limit and force settings.
Weather seals, framing and the opening
A door is only as good as the opening it sits in. The technician looks at the weather seal along the bottom and the stops at the sides and top, checking that they are intact, flexible and sealing. A cracked or hardened seal lets in water and insects and often indicates a door that has been in the sun for a long time. They look at the jamb and the header to check for rot, cracks, water damage and anything that affects how the door is mounted.
In many South Florida homes the framing around the garage door is wood, and it takes a lot of moisture. A technician cannot do structural repairs, but they can tell you when the wood looks soft or stained and recommend that a carpenter look at it. They will also check how the tracks are fastened to the wall and ceiling, because loose or corroded fasteners can let a track shift under load.
Hurricane season is on every South Florida owner's mind, and a technician can comment on the visible condition of the door and its hardware in that light. They cannot certify that a door will survive a particular storm, and they will not promise that. But they can tell you whether the hardware looks sound, whether the door seems suited to its opening and whether it is worth discussing a stronger door. Our guide to wind ratings explains what the labels mean.
Lubrication, tightening and small adjustments
Once the technician has completed the checks, they typically carry out routine maintenance. That means tightening loose hardware, lubricating the parts that need it with the right products, cleaning tracks where needed and adjusting settings that have drifted. They know which parts to lubricate and which to leave alone, and they can lubricate parts that an owner should not reach, with the proper precautions.
Small adjustments may include fine-tuning the opener's limits, correcting sensor alignment, adjusting a roller or tightening a hinge. If balance is slightly off, they may adjust spring tension with proper winding bars, but only if the springs are in good condition and the door is secured. If the springs are worn, they will recommend replacement instead of adjustment.
None of these tasks should be improvised. A loose bolt may be a sign that something is moving more than it should, and tightening it without understanding why can hide a larger problem. A technician will usually check why the bolt loosened, for example a vibration from an unbalanced door, and address the cause.
A scenario: the inspection that found a cable end
Consider a homeowner in Pompano Beach whose door has never given trouble. It is a steel sectional door about a mile from the water, and she books an inspection mainly because a neighbor mentioned it before storm season. She tells the technician the door seems slightly louder than it used to be, and that is all.
The technician runs the door and hears a faint scrape near the top. Looking closer, he finds a roller with a flat spot and a hinge that has started to crack. He then checks the cables and notices that the lower end of the right-hand cable, near the bottom bracket, is rusted and has a few broken strands. None of this was visible from the floor, and the door was working normally.
He explains that the cable is the more serious find, because a cable that parts under load can drop one side of the door and damage the panels and the track. He shows her the broken strands. The roller and hinge are routine replacements. The springs, he reports, still have life but are in the middle of their expected range, so they can be watched. She decides to replace the cable and the worn parts during the visit.
The outcome is a door that is quiet again, a cable that will not fail in the next storm and a note about the springs to revisit next time. That is a typical result of an inspection: not drama, but a handful of small findings that would have turned into a stuck door at an inconvenient time. If you have a door that seems fine but has never been looked at, this is the kind of thing a visit can find.
How an inspection differs for different door types
The core of the inspection is the same for every door, but the emphasis shifts with the type. A torsion spring door puts more focus on the bar, the cones and the bearing plates at the center and ends. An extension spring door puts more focus on the safety cables, the pulleys and the track hangers. A wood door gets a close look at moisture, rot and the finish. A glass and aluminum door gets attention for the seals and the glazing. An insulated door gets a look at the skin and the foam for delamination.
Door weight and size matter too. A double-width door is heavier and more prone to flexing, so the technician looks at the struts and the hinges. A door with added windows or modifications may have springs that no longer match its weight. A door with bracing for wind may need heavier hardware. Mention any of these when you book, so the technician knows what to expect.
Openers vary just as much. A chain drive, a belt drive, a screw drive and a wall-mounted jackshaft each have their own wear points and settings. The technician will tailor the opener checks to the type. If you are curious about the differences, our page on opener types describes them in plain language. If the opener is old and parts are scarce, the technician may discuss replacement as an option, but only once the door itself is in good order.
What the technician should tell you afterwards
A useful inspection ends with a clear report. The technician should explain, in plain language, what they inspected, what they found and what they recommend. A good technician sorts the findings into three groups: items in good condition, items that are worn but can wait and items that should be handled soon. They should show you worn or damaged parts when it is practical, and explain why each matters.
You should be told what any recommended repair involves before it begins. Quotes for repairs are given by phone when the problem is clear, and larger or more complicated work needs an on-site visit before a quote is given. You are never obliged to approve a repair on the spot, and a good technician does not pressure you. If you want to think about it, say so. If the door is unsafe to use, they will tell you why and what has to happen first.
Ask for a summary you can keep, even if it is a short note or a message. It becomes part of the log we recommend in our maintenance schedule guide, and it helps the next technician who works on the door. It also helps you plan for parts that are wearing, so replacement happens on your terms.
How to prepare for the visit
A little preparation makes the inspection faster and more useful. Clear the area around the door and the garage floor so the technician can work safely. Move vehicles out of the garage. Make sure someone is available to let the technician in and to answer questions. If you have the opener manual, remote instructions or any earlier paperwork, have it ready.
Write down what you have noticed: noises, slow movement, sensors that act up, remotes that misbehave, water coming in, rust spots. Include dates if you can, and share any photos. Mention if the door has been repaired or modified, if anyone has adjusted the springs or if it has been through a storm or flood. These details help the technician focus.
Finally, think about what you want to know. Are you wondering about hurricane readiness, replacing the opener, adding a keypad or adding a battery backup? An inspection is a good opportunity to ask. When you are ready, call and describe the door and what you have seen. The dispatcher will explain the service call charge before anyone is sent. We do not promise arrival windows, because timing depends on the day and other calls.
Questions people ask
How often should I schedule an inspection?
It depends on use, age and exposure. A heavily used door or one near salt water may justify a yearly visit or more often. A lightly used door in a sheltered garage may need less. Any time the door changes, such as new noises, slow movement or sagging, is a good reason to book regardless of the calendar.
Does an inspection mean repairs will be needed?
Not necessarily. Many inspections confirm that the door is in good condition and make only small adjustments. If something is wearing, the technician will explain what and why, and you can decide what to do. You are not obliged to approve repairs on the spot.
What should I do before the technician arrives?
Clear the garage floor and the area around the door, move vehicles out, make sure someone can let the technician in and write down what you have noticed. Photos of any problem and any paperwork you have for the door or opener are useful. Do not touch the springs or cables beforehand.
Can a technician tell me whether my door will survive a hurricane?
No one can promise that. A technician can look at the visible condition of the door and its hardware, comment on whether it seems suited to the opening and discuss stronger options. For wind questions, the door's product approval labels and a larger conversation about replacement may be relevant.
Will the technician test the safety sensors?
Yes. Testing the photo-eye sensors and the contact reversal is a standard part of an inspection, along with the opener's limits and force settings. If any safety device fails, the technician will find the cause and correct it before leaving the door in service.
Do you quote the cost of an inspection online?
No. Quotes are given by phone only, and the service call charge is explained before a technician is sent. If a larger or more complicated job comes out of the inspection, an on-site visit is needed before that quote can be given. Call and the dispatcher will explain.
If "The Annual Garage Door Inspection" is the problem at your house, call and describe what the door is doing. We explain what a repair visit would cover, and the service call charge is stated on the phone before anyone is dispatched.
