24 HOUR GARAGE DOOR REPAIRCall (844) 914-2600
Home › Repair Problems

Garage Door Will Not Stay Open

You lift the door, let go, and it drifts back down. Or the opener raises it and it creeps closed on its own. A door that cannot hold its position is telling you that the weight it carries is no longer being balanced, and the fix depends on which part is letting go.

Call (844) 914-2600

A 24 Hour Garage Door Repair technician on a ladder adjusting a torsion spring while a branded van waits in the driveway at sunset.

Two different problems that look alike

People describe a door that falls after opening in two ways, and it helps to separate them because they point in different directions. The first is a door lifted by hand, with the opener disconnected, that will not stay up. You raise it halfway, let go, and it descends, sometimes slowly, sometimes quickly. The second is a door raised by the opener that reaches the open position and then slowly creeps down, or drops after the opener stops, or closes by itself without a command.

The first problem is almost always about balance. A balanced door is held in place by springs, and when the springs weaken the door becomes heavy and wants to close. The second problem can have more than one cause. If the door is heavy because of weak springs, the opener may hold it during the cycle, but once the opener's clutch or brake releases or a drive part slips, the door slides down. It can also come from an opener that is failing to hold, a stripped gear, a slipping chain or belt, or a faulty limit or logic board that tells the door to close.

Distinguishing between them matters because the repairs are different. Heavy springs call for a spring replacement and a balance check. A failing opener holding mechanism calls for opener repair. Treating one as the other wastes money and leaves the door unsafe. In both cases the door can fall suddenly, so the first rule is to keep people and vehicles out from under it.

The hand-lifted door that will not stay up

Suppose you pull the release, lift the door to waist height and it falls. That behavior means the lifting force of the springs is lower than the weight of the door, at least in that part of the travel. A door with correctly sized, healthy springs hangs nearly weightless in the middle of its path. As the door rises, the springs unwind and the force changes, which is why a balanced door can still have a small preference to move at the extremes, but it should not slam.

Common reasons for the loss of lift include weakened or broken torsion springs, a spring that has lost some of its wound turns, a worn extension spring, a cable that has slipped, or a door that has become heavier. Springs that were wound a little low at installation will also let the door settle. Over years, the winding can relax slightly, particularly if the set screws on the cones were not tightened well. That is one reason to avoid any do-it-yourself winding.

If the door drops by hand, do not stand under it and do not keep testing. Each test is a chance for it to fall on you. A door that has to be held up is not safe to use. Keep it closed if it is closed, and if it is up, keep people and cars clear. A technician will check the balance with proper equipment and tell you whether the springs need winding or replacing. The page on doors that slam shut describes related behavior.

  • Do not stand under or reach into a door that will not stay up.
  • Do not try to wind or tighten springs to compensate.
  • Keep vehicles out of the doorway while the door is in this state.
  • Close the door and leave it closed if it is safe to do so.

Springs, winding and the loss of tension

The springs are the first suspect, and for good reason. A torsion spring is a coiled steel bar that is wound a set number of turns to carry the weight of the door. Over time the spring loses a little force with each cycle, and the number of turns it holds can effectively drift. A spring that has cracked will release its energy and the door becomes heavy at once. A spring that is merely tired lets the door sag gradually.

A door with two springs can hide the problem for a while. If one breaks, the other still carries part of the load, and the door feels heavier than it used to without being impossible. Many owners discover only when the second spring fails or when the opener complains. A door that has lost one spring is very much at risk, since the remaining spring is working harder and the balance is poor.

Weather shortens spring life. Salt air corrodes the coil surfaces, and humidity encourages rust at the points where the coils touch each other. In Broward, Palm Beach and Miami-Dade, a spring near the coast may not reach the cycle life it would in a dry region. If your door drifts down and the springs look rusted, that is a clue. See the pages on the torsion spring and the spring repair process for more detail.

Cables, drums and uneven lift

The cables connect the springs to the bottom of the door, running over drums at each end of the torsion shaft. If a cable slips off its drum, loosens, or frays, the lifting force no longer reaches the door evenly. One side may hold and the other sag, causing the door to tilt and sometimes drift. A cable that has partly stretched or a drum that has shifted on its shaft changes the geometry in the same way.

You might notice a cable that hangs with slack, a door that is crooked at the bottom, or a noise like a snap earlier. A door with a loose cable is dangerous because it can drop abruptly and the loose cable can tangle in the track or rollers. If you see slack, do not attempt to push the cable back or tighten it. The cable is under tension from the spring when the door is down, and it can whip.

Technicians will inspect the cable path, the drums and the bottom brackets, and replace parts that are frayed or worn. Cable replacement often goes together with spring replacement, since both are part of the lifting system. A good repair restores even lift on both sides and a door that stays where it is put. The page on garage door cables explains how the parts work.

The opener-lifted door that creeps down

If the door is raised by the opener, reaches the top, and then slowly settles or drops, the opener is not holding it. Some openers rely on the gear train and the motor to hold the door in place when the unit stops. Others rely on a brake or a clutch. When these parts wear, the door can back-drive the opener, pulling the chain or belt backward and descending.

The trouble can be in the drive parts: a stripped plastic gear, a worn sprocket, a slipping chain, a belt with a damaged section, or a trolley that has come loose. It can also be a heavy door: if the springs have weakened, the door's weight overcomes the opener's holding ability. The opener may seem to work well in daily use because the motor holds the load during the cycle, but once it stops, the door descends.

A particularly worrying version is a door that closes by itself when no one has pressed a button. That can be a drive failure, a board issue or a stray signal. The page on a door that opens by itself covers unexpected movement from the control side, and the pages on opener motor and gear problems describe the parts. A door that closes unexpectedly is a hazard for people and vehicles in the doorway.

Limit settings, sensors and logic that tell the door to close

Sometimes the door falls because the opener tells it to. The up limit determines where the opener stops raising the door, and if it is set slightly off, the door may stop at a position that the opener does not recognize as fully open. The unit may then try to correct and move the door further or let it settle. A fault in the limit sensing can lead the opener to run down instead of holding.

Auto-close features, timers and smart modules can also close the door on a schedule or after a delay. If you recently added a smart accessory, a timer to close or a new remote, check whether those features are active. A wall control in a lock or vacation mode, or a stuck button, may produce commands you did not intend. A shorted wall button wire can send a constant close signal.

These issues are not about weight, and the door may feel balanced by hand. The test is to disconnect the opener, lift by hand and see whether the door stays up. If it does stay up, the problem is on the opener side, and a technician can check the limits, the logic board and the controls. If it does not stay up, the problem is the springs or cables, and the opener is not the cause.

What is safe to check and what is not

From the floor, with the door closed, you can look at the springs and cables for obvious damage, note whether the door is level, and check whether the opener's manual release has been pulled. You can check the wall control and the remotes for stuck buttons and for lock mode. You can check whether any timer or smart feature is set to close the door.

A hand-lift test is reasonable only if you are comfortable with the weight and have a clear space. Lift only a little, with your body beside the door and not beneath it. If the door feels heavy, stop at once. Never leave the door held open by your hands or a prop while you look at anything. Keep other people out of the area.

Do not touch the springs, cable ends, bottom brackets or drum set screws. Do not try to rewind or tighten anything, and do not climb up to look closely while the door can move. If the door is stuck partly open and drifting, keep clear and call. A drifting door can fall without warning, and the best protection is distance.

  1. Look at the springs and cables from the floor without touching them.
  2. Check the wall control for lock mode and the remotes for stuck buttons.
  3. Check for a smart or timer feature that might close the door.
  4. If the door is closed, leave it closed and avoid testing it by hand.
  5. Take photos from a safe angle and note what the door does.

Examples from ordinary South Florida garages

A homeowner in Miramar raises the door to put a bike inside and notices that it sinks slowly after being released, about a foot every few seconds. The door has always been a little lazy, but this is new. The technician finds that one of the two torsion springs has a hairline fracture and the other has lost most of its force. Both are replaced, the cables and drums are checked, and the door stays at any height afterward.

A condo owner in Aventura reports that the door opens, stays up for a moment and then closes by itself while the car is backing out. The springs are fine and the door stays up by hand. The fault is in the opener: a worn plastic gear that lets the carriage slip when the motor stops. The gear and the drive parts are replaced, and the door holds again. The owner had assumed the door was merely misadjusted.

A family in Wellington adds a smart garage controller and later finds the door closing on a schedule they did not set. The accessory had an auto-close option turned on by default, and it was closing the door after a few minutes. Nothing in the door was broken at all. Turning off the feature solved it, and the technician's visit confirmed that the springs, cables and opener were in good shape.

These cases show why a careful first step matters. The same symptom can be a broken spring, a worn gear or a setting, and the safe and economical path is to find out which before replacing parts. Describing exactly how the door behaves, by hand and with the opener, is the best help you can give.

What the visit looks like and what to do in the meantime

The technician will begin by securing the door and then separating the two possibilities. With the opener disconnected, the door's balance is tested. If it falls, the springs and cables are examined and replaced or adjusted as needed, and the whole lifting system is checked. If it stays up, the opener is tested: drive parts, limits, brake or clutch, wall control and logic board.

Repairs range from a spring and cable replacement to a drive part or a board replacement. The technician will explain the condition in plain terms and give a quote by phone for straightforward work, or on site for complicated jobs, with a service call charge explained before dispatch. After the repair, the door should hold at any height and the opener should stop and hold it reliably.

In the meantime, keep the door closed if you can. If it is stuck open, keep vehicles and people clear and secure the garage as best you can. Do not use the opener repeatedly on a door that falls. Call, describe whether it falls by hand or after the opener, and what you saw, and the next steps will be explained on the phone. A door that will not stay open is not just inconvenient, it is a sign that something in the system needs attention.

Questions people ask

Why does my garage door fall when I lift it by hand?

Usually the springs no longer balance the weight of the door. They may be weak, broken or wound too low, or a cable may have slipped. A balanced door should stay roughly where you leave it. A door that drops is dangerous to keep testing, so keep clear and have a technician check the lifting system.

My door opens fine with the opener but creeps down afterward. Why?

The opener may not be holding the door. A worn gear, slipping chain or belt, or a failing brake or clutch can let the door back-drive, and a heavy door from weak springs makes it worse. Disconnect the opener and test by hand, carefully, to tell whether the problem is the springs or the opener.

Could a broken spring make the door fall down by itself?

A broken spring makes the door heavy, and a heavy door can close quickly or drift down once the opener lets go. If a spring broke, you may have heard a loud bang. Do not stand under the door or try to lift it. A technician needs to replace the spring and check the cables and drums.

Can the door close by itself without anyone pressing a button?

Yes, in several ways. A drive part may be slipping, a limit or board fault may command closing, an auto-close timer or smart module may be active, or a wall button may be shorted. Check for such features and call if it continues. Keep people and vehicles clear of the doorway while it is unresolved.

What should I do until the door is repaired?

Keep the door closed if you can, keep people, pets and vehicles away from under it, and avoid lifting it by hand. Do not prop it with ladders or boards. Keep remotes away from children. If it is stuck open, mention that when you call so the security of the property can be considered.

Talk to 24 Hour Garage Door Repair

For "Garage Door Will Not Stay Open", a phone call comes first. Describe the springs, the opener or the panels, and we will explain how the work is done and what the visit charge covers.

Call (844) 914-2600