The four seals around a garage door
A garage door has weather stripping on every edge, and each one has a different job. The bottom seal, also called the bottom astragal or door sweep, is a flexible strip fastened to the lower edge of the door that presses against the floor when the door closes. The side seals, often called jamb or stop molding seals, run vertically along both sides of the opening and press against the door edges. The top seal runs across the header and meets the top of the door. And between sections, a panel joint seal or a built-in lip keeps water from running through the seams.
Together these strips close the small gaps that exist between a moving door and a fixed opening. Those gaps have to exist, because the door must be able to move. The seals bridge them with flexible material that compresses a little when the door is closed and springs back when it opens.
If one seal fails, the others cannot make up for it. A worn bottom seal lets water crawl under the door in a heavy rain even if the side seals are perfect. Torn side seals let wind-driven rain and insects in around the edges. A missing top seal lets warm, humid air and rainwater into the header area. Each seal needs to be judged on its own.
- Bottom seal: seals against the floor and is the most exposed to water and wear.
- Side seals: seal the vertical gaps between door and jamb.
- Top seal: seals the header gap and keeps out rain and dust.
- Panel joint seals: limit water and air movement between sections.
What seals are made of and why it matters
Seals come in several materials. Vinyl, often called PVC, is common for side and top stripping and is made in flat, bulb or flap shapes. Rubber, usually EPDM or similar synthetic rubber, is common for bottom seals and stays flexible across a wider temperature range. Some seals use a vinyl bulb or flap and an aluminum or plastic retainer that slides into a slot on the door.
Material determines how a seal ages. Vinyl can harden and crack under strong sunlight and heat. Cheaper rubber can go sticky or powdery. Higher quality seals last longer and keep their shape better, but even good ones are consumable parts, much like wiper blades or tires. They are supposed to wear out and be replaced.
South Florida conditions are tough on every material. Ultraviolet light in summer, high heat inside the garage, constant humidity, and in some places salt carried on the breeze all attack seals. Seals on the sunny side of a house may fail years before those on the shaded side. Seals that sit in standing water at the floor can swell, rot or grow mildew.
Why seals matter in a wet, humid climate
In a dry region a worn seal is a small matter. Here it can be a recurring nuisance and a source of property damage. Heavy summer rains push water against the garage door at speed, and wind-driven rain during tropical systems can force water through gaps of surprisingly small size. Water that gets under the door wets stored boxes, soaks the floor, damages drywall and finishes, and can reach electrical equipment and the bottom edge of the door itself.
A good seal also helps control pests. Gaps at the bottom and sides let in ants, roaches, lizards, rodents and sometimes larger animals, and a worn bottom seal is one of the most common entry routes. The page on pest entry goes into how animals use those gaps.
Humidity is another reason. Garages are often not air conditioned, and humid air that gets in condenses on cool surfaces, feeding mildew and rust on tools and stored items. A tight seal does not make the garage dry, but it reduces the amount of moist air that flows in.
Finally, the bottom seal protects the door itself. A seal in good shape stands between the lower edge of the door and the water on the floor. Without it, the bottom panel soaks, rusts or rots, and the bottom bracket area starts to deteriorate. The page on bottom brackets shows why that area matters.
Signs a seal has failed
Seal failure is usually visible and easy to check. Start with the bottom. With the door closed, look along the base from inside. Is there a gap of daylight between the seal and the floor? Is the seal cracked, flattened, torn or missing in places? Does it curl or fold under rather than pressing flat? Can you see the retainer or the metal edge of the door where the rubber used to be?
On a bright day, switch off the garage lights and look for light leaking around the edges. Light that shows around the sides or top points to gaps. Run a hand lightly along the side seals, being careful not to touch any moving parts or springs, and feel for brittleness, cracks or gaps where the seal has pulled out of its groove.
Other signs show up inside the garage. Water stains along the floor at the door line after rain. Leaves and dust blown in. Insects or lizards living near the threshold. A persistent musty smell near the door. A draft you can feel on a windy day.
Do not rely on a single sign. A seal that looks fine from the inside may be failing where you cannot see, and a floor that sits lower than the driveway can allow water in even when the seal is perfect. A technician can help distinguish a seal problem from a slope or drainage problem.
- Daylight visible under or around the closed door.
- Bottom seal cracked, flattened, torn, curled or missing.
- Side stripping brittle, gapped or pulled out of its channel.
- Water stains or puddles at the door line after rain.
- Pests, leaves or dust accumulating near the threshold.
- A draft or musty odor close to the door.
Seals, the floor and the driveway
Sometimes a good seal is not enough, because the problem is the surface it meets. A bottom seal can only close a gap that is a few inches at most, and only if the floor is reasonably level. If the slab slopes, has a dip or has cracked and settled, the seal will meet the floor unevenly, leaving a gap at one end. Seals are made flexible to cope with small irregularities, not large ones.
Drainage matters as well. In many South Florida neighborhoods, the driveway slopes toward the garage, or the grade at the door is lower than the lawn. During heavy rain water follows the slope into the garage, and no seal can hold back a depth of water pressing against it. In flood-prone areas, the seal is one part of a larger picture. See the guide on flood water and garage doors for what happens when water is deeper than a seal can handle.
A technician looking at a leaky door will check both the seal and the floor. They may suggest a taller or different style of bottom seal, a threshold seal that is fastened to the floor, or a simple repair to the slab or apron if that is practical. Some of those are carpentry or concrete jobs, and the technician will say honestly what falls outside door work.
What an owner can do to extend seal life
Seals last longer with a little care. Wipe the bottom seal and the lower edge of the door with a mild soap solution and a soft cloth every so often to remove dirt, mildew and grit. Rinse and let it dry. Keep the area under the door clear of leaves and debris, which hold water against the seal.
Keep sprinklers pointed away from the door, because daily spray soaks the seal and lower panel. Avoid harsh solvents, petroleum-based products or strong cleaners on rubber and vinyl, since they can dry or soften the material. A light application of a silicone-based product made for rubber and vinyl is sometimes used to keep seals supple, but follow the product directions and avoid getting it on the floor where it could make it slippery.
A word of caution about repairs. Seals are usually held in place by retainers or grooves, and replacing them is not as dangerous as working on springs. But the bottom seal sits at the lower edge of the door, close to the bottom brackets and cables, which are under tension. Do not reach into or near the bottom corners, and do not remove anything that looks like part of the cable fixture. If you are not sure, ask a technician.
How replacement works and what a technician looks for
Replacing a bottom seal usually involves sliding the old strip out of its retainer, cleaning the track in the retainer, and sliding in a new strip cut to length. Some doors use a seal that is nailed or screwed on, or pressed into a channel. The right replacement depends on the retainer type, which is often a double channel, a single channel, or a bulb-and-flap design. Choosing the wrong profile leaves a gap, even if the length is right.
A technician checks the retainer too. A bent or corroded retainer will not hold a new seal. They check the bottom edge of the door for rust or rot, and the alignment of the door at the floor. If the door sits crooked, a new seal will wear unevenly and leak at one end. In that case the repair may need to address alignment first.
Side and top seals are replaced by removing the stop molding or pulling the old stripping from its groove and fitting a new length. On some doors the stripping is part of a wooden stop that is nailed to the jamb, and on others it is a separate vinyl piece with its own flange. Matching the profile and the thickness matters, since too thick a seal drags on the door and too thin a one leaves gaps.
The right choice depends on the door, the climate exposure and how the garage is used. Details are given by phone. Quotes are not published, and a service call charge applies for visits, explained before dispatch.
Seals on different door types and materials
Seal choices vary with the door. Steel doors with a retainer channel at the bottom accept a replaceable rubber or vinyl strip. Wood doors often use a strip nailed or screwed to the bottom rail, and the wood itself must be sound to hold fasteners. Aluminum and glass doors use specific profiles that slide into aluminum channels. Fiberglass and composite doors use retainers shaped to their sections.
Doors with wind ratings and impact ratings are tested with their seals in place. Replacing a seal with a very different profile can change how a door performs, and in the case of rated assemblies, a technician matches the replacement to the door's design. For background, see the guides to wind ratings and impact-rated doors.
Insulated doors depend on their seals more than non-insulated ones. The insulation is wasted if warm, humid air flows around the edges. If you have invested in an insulated door for comfort or noise control, keeping the seals tight is part of getting what you intended. The guide on insulation, noise and heat covers that side.
Preparing for the call
When you call, describe what you see. Say which seal seems to be the problem: the bottom, the sides, the top or all three. Describe whether it is cracked, flattened, missing or pulled out. Say whether water comes in during rain, whether pests are getting in, or whether you simply see daylight around the door.
Mention the door material and approximate width, and whether it is an insulated or non-insulated door. A photo of the bottom edge, with the door closed and the seal in view, helps the technician identify the retainer type. If you can see a label or model number, mention it.
Say whether you have noticed any slope or low spot at the threshold, and whether the problem is worse during heavy rain. That helps separate a seal issue from a drainage one. A service call charge applies and is explained on the phone before dispatch, and no arrival time is promised. If water, pests or drafts are coming in, call and describe what you see, and a technician can advise what is practical.
Questions people ask
How long do garage door seals last in Florida?
There is no fixed lifespan. Sun, heat, humidity, salt and standing water all shorten it, and seals on sunny sides of a house usually age faster. Check them a couple of times a year. Cracking, flattening, hardening, gaps or visible daylight all suggest it is time to have them replaced.
Will a new bottom seal stop water coming in?
It helps with the gap between the door and the floor, but it cannot hold back deep or fast-moving water, and it cannot fix a slab that slopes toward the garage. A technician can check the seal and the floor together and tell you honestly whether a new seal is likely to solve the problem.
Can I replace the bottom seal myself?
Many owners do slide a new strip into a retainer, but the lower corners of the door hold cables under heavy tension, so keep hands away from the bottom brackets and fixtures. If the retainer is bent, the bottom edge is damaged, or you are unsure which profile you need, a technician can handle it.
Why do pests come in under my door?
Insects, lizards and rodents use any gap they can find, and a worn or missing bottom seal is a common one. Gaps at the sides and corners also matter. Replacing damaged seals and keeping the area around the door clean reduces entry points, though it is not a substitute for pest control where there is an infestation.
Is stripping the same as a seal?
In everyday use the terms overlap. Stripping or weather stripping usually refers to the vinyl or rubber strips along the sides and top, while the bottom seal is also called a sweep or astragal. A technician will ask which edge is the problem and identify the right profile for it.
Do insulated doors need different seals?
They use the same general types, but tight seals matter more because insulation loses value when warm, humid air flows around the edges. Rated doors should have replacement seals that match the original design. Mention the door type and any labels when you call so the technician can bring the right parts.
For "Weather Seals and Stripping", a phone call comes first. Describe the springs, the opener or the panels, and we will explain how the work is done and what the visit charge covers.
